Poulan 96194000503 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Voitures Poulan 96194000503. Poulan 96194000503 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 56
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
OWNER'S MANUAL
MODEL NUMBER:
96194000503
SNOW THROWER
Always Wear Eye Protection During Operation
IMPORTANT MANUAL Do Not Throw Away
WARNING:
Read the Owner's Manual and
fol low all Warnings and Safety
In struc tions. Fail ure to do so
can result in serious injury.
421894 08.21.08 TH
Printed in U.S.A.
Vue de la page 0
1 2 3 4 5 6 ... 55 56

Résumé du contenu

Page 1 - 96194000503

OWNER'S MANUALMODEL NUMBER:96194000503SNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read th

Page 2 - IMPORTANT

10TO MOVE FORWARD AND BACKWARD (See Fig. 14)SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive con

Page 3 - TABLE OF CONTENTS

11TO ADJUST SKID PLATES (See Fig. 15)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each

Page 4 - ASSEMBLY / PRE-OPERATION

12OPERATIONTO START ENGINE Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter

Page 5

13GENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. To re

Page 6

14MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention

Page 7

153. Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 lockn

Page 8

16SERVICE AND ADJUSTMENTS1. REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or f

Page 9

17SERVICE AND ADJUSTMENTSSTORAGEImmediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more

Page 10 - OPERATION

18Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition

Page 11

19ADVERTENCIA: Siempre desconecte el alambre de la bujía y póngalo donde no pueda entrar en contacto con la bujía, para evitar el arranque por acciden

Page 12

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

Page 13 - MAINTENANCE

204. Si la unidad empezara a vibrar de manera anormal, parar el motor y controlar inmediatamente para detectar la causa. Las vibraciones son generalm

Page 14

21MONTAJE / PRE-OPERACIÓNPARTES EMPACADAS POR SEPARADO EL LA CAJA DE CARTÓN(1) CABLE DE ALIMENTACIÓN(198563)(1) CONDUCTO LA DESCARGA(3) RESORTES DE RE

Page 15 - SERVICE AND ADJUSTMENTS

22COMO PREPARAR SUMÁQUINA QUITANIEVES PORTAHERRAMIENTAS (Ver Fig. 8)Con su máquina quitanieves se le proporciona un portaherra-mientas. El portaherram

Page 16

23MONTAJE / PRE-OPERACIÓNBIELA DE MANDO DE LA BARRENA BRAZO DE MANDO MANGUITO DE CAUCHO APERTURA GANCHO FIG. 5MONTAR LA BIELADE MANDO DE LA BARRENA (

Page 17

24OPERACIÓNFAMILIARÍCESE CON SU MÁQUINA QUITANIEVESLEA ESTE MANUAL DEL DUEÑO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU MÁQUINA QUITANIEVES.Compare

Page 18 - TROUBLESHOOTING

25PALANCA DE CONTROL DE LATRAC-CIÓNOPERACIÓNCUMPLE CON LOS REQUISITOS DE SEGURIDAD DE LA A.N.S.I.Nuestras máquina quitanieves cumplen con los estándar

Page 19 - IMPORTANTE

26OPERACIÓNLa operación de cualquier máquina quitanieves puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños grave

Page 20 - TABLA DE MATERIAS

27USAR LA HERRAMIENTA PARA LIMPIAR(Ver Fig. 13) En ciertas condiciones de la nieve, el conducto de descarga pu-ede atascarse con hielo y nieve. Usar

Page 21 - MONTAJE / PRE-OPERACIÓN

28OPERACIÓNREGULAR LAS PLACAS DE DESLIZAMIENTO(Ver Fig. 15) NOTA: la llave de apriete proporcionada en su bolsa de partes puede utilizarse para regula

Page 22

29OPERACIÓN• Asegúrese que la instalación eléctrica de su casa sea un sistema de tres hilos puesta a tierra de 120 Voltios A.C. Si no está seguro, co

Page 23 - MONTAR LA BIELA

36. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impeller and all moving parts have stoppe

Page 24 - OPERACIÓN

30MANTENAMIENTORECOMENDACIONES GENERALESLa garantía de esta maquina quitanieves no cubre los artículos que han estado sujetos al abuso o a la negligen

Page 25

31MANTENAMIENTOCORREAS EN VControlar el deterioro y el desgaste de las correas en V después de 50 horas de funcionamiento y sustituir si fuera necesar

Page 26 - (Ver Fig. 9)

32SERVICIO Y ADJUSTESADVERTENCIA: Para evitar lesiónes serias, an-tes de dar calquier servico o de hacer ajustes:1. Asegurarse el interruptor de ON/O

Page 27 - LANZAR LA NIEVE (Ver Fig. 12)

33SERVICIO Y ADJUSTES1. VACIAR LA GASOLINA DEL DEPÓSITO DE CARBURANTE – Vaciar la gasolina del depósito del carburante en un con-tenedor apropiado,

Page 28

34ALMACENIMIENTODESMONTAR LAS RUEDAS (Ver Fig. 20)• Desmontar el perno de lingüete y desmontar la rueda del eje.IMPORTANTE: Cuando se instala la rued

Page 29 - ANTES DE PARAR

35IDENTIFICACION DE PROBLEMASNo arranca 1. Válvula del combustible está OFF. 1. Gire a la válvula del combustible a la posición ON. 2. La llave

Page 30 - ANTES DE CADA USO

36REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503AUGER HOUSING / IMPELLER ASSEMBLY2 (EXPLODED)2109111113121241314151787115611161835192122232425

Page 31 - MANTENAMIENTO

37REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches. 1 in

Page 32 - CONDUCTO DEFLECTOR

38NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 33 - SERVICIO Y ADJUSTES

39NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 34 - ALMACENIMIENTO

4PARTS PACKED SEPARATELY IN CARTONASSEMBLY / PRE-OPERATIONRead these instructions and this manual in its entirety before you attempt to assemble or op

Page 35 - IDENTIFICACION DE PROBLEMAS

40REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503CONTROL PANEL / DISCHARGE CHUTE12345667891111111001.09.001-AKEY PARTNO. NO. DESCRIPTION

Page 36

41REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503CONTROL PANEL / DISCHARGE CHUTEKEY PARTNO. NO. DESCRIPTION NOTE: All component dimensio

Page 37

42REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use

Page 38 - 01.07.008-A

43REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use

Page 39 - 01.07.005-A

44REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503HANDLESKEY PARTNO. NO. DESCRIPTION 12345657891001.12.001-A1 180480 IMPELLER ROD ASSE

Page 40 - 01.09.001-A

45REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503HANDLESKEY PARTNO. NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches.

Page 41

46REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503DRIVE01.02.003-D312928262726253024244414040365768976101112119976133739763676387615141620192144

Page 42 - 01.08.002-D

47REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use o

Page 43 - 01.05.002-B

48REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use o

Page 44

49REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503CHASSIS / ENGINE / PULLEYSKEY PARTNO. NO. DESCRIPTION KEY PARTNO. NO. DESCRIPTION

Page 45 - 01.10.003-B

5HOW TO SET UP YOUR SNOW THROWER TOOL BOX (See Fig. 8)A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. St

Page 46

50NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 47

51NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 48 - 01.03.005-A

525314217689REPAIR PARTS SNOW THROWER - MODEL NUMBER 96194000503DECALS 1 181038 DECAL, DANGER 2 422041 DECAL, POULAN, 800S / 24" 3 181034

Page 49 - 01.04.019-A

53SERVICE NOTES

Page 50 - 01.06.001-A

54SERVICE NOTES

Page 51 - 01.14.007-A

55SERVICE NOTES

Page 52

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w

Page 53 - SERVICE NOTES

6ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

Page 54

7OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

Page 55

8OPERATIONThrottle/engine control - used to se lect either FAST or SLOW engine speed and to STOP the engine.Traction drive control lever - used to eng

Page 56 - LIMITED WARRANTY

9The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glas

Commentaires sur ces manuels

Pas de commentaire