Poulan 420915 Manuel d'utilisateur

OWNER'S MANUALMODEL NUMBER:PP11530ESSNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the

10TO CONTROL SNOW DISCHARGE (See Fig. 14)WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma-

11• Squeeze traction drive control lever to handle to en gage the drive system.• Release traction drive control lever to stop the forward or reverse

12BEFORE STARTING THE ENGINECHECK ENGINE OIL LEVEL (See Fig. 21)The engine on your snow thrower has been shipped, from the factory, already filled wit

13TO START ENGINE • Be sure fuel shut-off valve is in the “OPEN” position.Your snow thrower engine is equipped with both a 120 Volt A.C. electric sta

14 SAE 5W-30 Motor Oil See “ENGINE” inMaintenance section General Purpose GreaseGENERAL REC OM MEN DA TIONSThe warranty on this snow thrower d

15MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention

163. Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 lockn

171. REMOVE GASOLINE FROM FUEL TANK - Drain gaso-line from fuel tank into a suitable container, out doors, away from fire or flame. Wipe up any spill

18SERVICE AND ADJUSTMENTSSTORAGEImmediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more

19Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

20REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)AUGER HOUSING / IMPELLER ASSEMBLY2 (EXPLODED)2109111113121241314151787115611161835192122

21REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

22REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)AUGER HOUSING / IMPELLER ASSEMBLYKEY PART NO. NO. DESCRIPTIONKEY PART NO

23REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)AUGER HOUSING / IMPELLER ASSEMBLYKEY PART NO. NO. DESCRIPTIONKEY PART NO

24REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)AUGER HOUSING / IMPELLER ASSEMBLY1253434125343401.16.001-AKEY PART NO. NO. D

25REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)CONTROL PANEL / DISCHARGE CHUTEKEY PART NO. NO. DESCRIPTION12466*11*12*8*9*1

26REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

27NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

28REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

29REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac tured to give best possible dependability and

30NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

31REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT

32REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)DRIVE31292826272625302424441404036548941011121199413373943643841514162019214417183233343

33REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)DRIVEKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTION1

34REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1 in

35NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

36REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)WHEELSKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTION12

37REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001902)BAG OF PARTSKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIP

38KEY PART NO. NO. DESCRIPTION 1 181037 DECAL, DANGER 2 187867 DECAL, POULAN PRO, 11 HP / 30" 3 181035 DECAL, DANGER, DEFLECTOR

39SERVICE NOTES

4PARTS PACKED SEPARATELY IN CARTON(1) POWER CORD(198563)(1) DISCHARGE CHUTE(2) SHEAR BOLTS 1/4-20 x 1-3/4(198636)(2) SPACERS(198638)(1) WASHER 3/8(191

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w

5Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual w

6ASSEMBLY / PRE-OPERATIONINSTALL TRACTION DRIVE CONTROL ROD(See Figs. 3 and 4)The traction drive control rod has the long loop on the end of the sprin

7ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

9OPERATIONThrottle/engine control - used to se lect either FAST or SLOW engine speed and to STOP the engine.Traction drive control lever - used to eng