OWNER'S MANUALMODEL NUMBER:PP208EPS24SNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the
10The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety gla
11OPERATIONTO THROW SNOW (See Fig. 13)The auger rotation is controlled by the auger control lever located on the right side handle.• Squeeze auger co
12TO ADJUST SKID PLATES (See Fig. 17)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each
13OPERATIONTO START ENGINE • Be sure fuel shut-off valve is in the “OPEN” position.Your snow thrower engine is equipped with both a 120 Volt A.C. ele
14MAINTENANCELUBRICATION CHARTGENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator
15MAINTENANCEV-BELTSCheck V-belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not ad just abl
16SERVICE AND ADJUSTMENTSWARNING: To avoid serious injury, before performing any service or ad just ments:1. Be sure the on/off switch is in the OFF p
17SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"
18SERVICE AND ADJUSTMENTSNOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer.
19STORAGEImmediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never
2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure
20TROUBLESHOOTINGDoes not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2.
21NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
22REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. in
23NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
24KEY PART NO. NO. DESCRIPTION1233401.11.001-B4KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inche
25REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702)CONTROL PANEL / CHUTEKEY PART NO. NO. DESCRIPTIONNOTE: All component
26NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
27NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
28NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
29NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
36. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel-ler and all moving parts have stopp
30NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
31KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm
32REPAIR PARTS SNOW THROWER - MODEL NUMBER PP208EPS24 (96198002702)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMP
33NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
34KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONNOTE: All component dimensi
35NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
36NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
37NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa
38KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTION01.14.009-A11 422663 SAF
39KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm
4PARTS PACKED SEPARATELY IN CARTONRead these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thro
LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w
5ASSEMBLY / PRE-OPERATIONSPEED CON TROL RODSPEED CONTROL BRACKETRETAINER SPRINGSPEED CONTROL LEVERFig. 2SPEEDCONTROL RODHANDLE KNOBLOWER HANDLEPLASTIC
6ASSEMBLY / PRE-OPERATIONAUGERCONTROL LEVERAUGER CONTROL RODAUGERCONTROL BRACKETRETAINER SPRINGFig. 6INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)1.
7ASSEMBLY / PRE-OPERATIONCHECK TIRE PRESSUREThe tires on your snow thrower were overinflated at the fac-tory for shipping purposes. Correct and equal
8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with
9OPERATIONLH and RH turn triggers - used to steer the snow thrower.Drive speed control lever - used to select forward or reverse motion and speed of s
Commentaires sur ces manuels