Poulan 210 Manuel d'utilisateur télécharger pdf (Page 19)

Н. TROUBLE SHOOTING CHART

SYMPTOM

CAUSE

REMEDY

Engine will not start

or will run only for

a few seconds

after starting.

1. Fuel tank empty.

2. Engine flooded.

3. Spark plug not firing.

4. Fuel not reaching carburetor.

5. Carburetor requires adjustment.

6. Stop switch off.

7. None of the above.

1. Fill tank with correct fuel mixture.

2. See “Starting Instructions.”

3. Install new plug/check ignition switch.

4. Replace fuel filter; inspect fuel line.

5. See “Carburetor Adjustments.”

6. Move switch to the “START” position.

7. Contact your Authorized Service Dealer.

Engine will not idle

properly.

1. Idle speed set too fast or too slow.

2. Low speed mixture requires adjustment.

3. Crankshaft seals worn.

4. Compre.ssion low.

5. None of the above.

1. See “Carburetor Adjustments.”

2. See “Carburetor Adjustments.”

3. Contact your Authorized Service Dealer.

4. Contact your Authorized Service Dealer.

5. Contact your Authorized Service Dealer.

Engine will not

accelerate, lacks

power, or dies

under a load.

1. Air filter dirty.

2. Spark plug fouled.

3. Carburetor requires adjustment.

4. Exhaust ports or muffler outlets plugged.

5. Compression low.

6. None of the above.

1. Clean or replace air filter.

2. Clean or replace spark plug and re-gap.

3. See “Carburetor Adjustments.”

4. Contact your Authorized Service Dealer.

5. Contact your Authorized Service Dealer.

6. Contact your Authorized Service Dealer.

Engine smokes

excessively.

1. Air filter dirty.

2. Fuel mixture incorrect.

3. High speed mixture requires adjustment.

4. Choke partially on.

1. Clean or replace air filter.

2. Refuel with correct fuel mixture.

3. See “Carburetor Adjustments.”

4. Push choke knob in.

Engine runs hot.

1. Fuel mixture incorrect.

2. High speed mixture set too low (Lean).

3. Spark plug incorrect. ,

4. Exhaust ports or muffler outlets plugged.

5. Carbon build-up on muffler outlet screen.

6. Fan housing/cylinder fins dirty.

7. None of the above.

1. See “Fueling Your Unit.”

2. See “Carburetor Adjustments.”

3. Replace with correct plug.

4. Contact your Authorized Service Dealer.

5. Clean spark arrestor screen.

6. Clean area.

7. Contact your Authorized Service Dealer.

Oil inadequate for bar

and chain lubrication.

1. Oil tank empty.

2. Oil pump or oil filter clogged.

3. Guide bar oil hole blocked.

1. Fill oil tank.

2. Contact your Authorized Service Dealer.

3. Remove bar and clean.

Chain moves at

idle speed.

1. Idle speed requires adjustment.

2. Clutch requires repair.

1. See “Carburetor Adjustments..”

2. Contact your Authorized Service Dealer.

Chain does not move

when engine is

accelerated.

1. Chain tension too tight.

2. Carburetor requires adjustment.

3. Guide bar rails pinched.

4. Clutch slipping.

5. Chain brake engaged.

1. See “Chain Tension.”

2. See “Carburetor Adjustments.”

3. Repair or replace.

4. Contact your Authorized Service Dealer.

5. Disengage chain brake.

Chain clatters or

cuts roughly.

1. Chain tension incorrect.

2. Cutters damaged.

3. Chain worn.

4. Cutters dull, improperly sharpened, or

depth gauges too high.

5. Sprocket worn.

6. Chain installed backwards.

1. See “Chain Tension.”

2. Contact your Authorized Service Dealer.

3. Resharpen or replace chain.

4. Have chain sharpened.

5. Contact your Authorized Service Dealer.

6. Install chain in right direction.

Chain stops within

the cut.

1. Chain cutter tops not filed flat.

2. Guide bar burred or bent; rails uneven.

3. Clutch slipping.

1. Have chain sharpened.

2. Repair or replace guide bar.

3. Contact your Authorized Service Dealer.

Chain cuts at an

angle.

1. Cutters damaged on one side.

2. Chain dull on one side.

3. Guide bar bent or worn.

1. Have chain sharpened.

2. Have chain sharpened.

3. Replace guide bar.

1 2 ... 14 15 16 17 18 19 20 21

Commentaires sur ces manuels

Pas de commentaire

Poulan 210 Manuel d'utilisateur Page 19

Commentaires sur ces manuels

Produits connexes et manuels pour Outil à essence Poulan 210