Poulan 530086667 Manuel d'utilisateur télécharger pdf (Page 10)

Push the choke knob in completely (to the

OFF position); pull the starter rope until the

engine starts.

OFF FULL

CHOKE

Choke knob

(SIDE VIEW)

Allow the engine to run for approximately 5

seconds. Then, squeeze and release

throttle trigger to allow engine to return to

idle speed.

STARTING A WARM ENGINE:

Move ON/STOP switch to the ON position.

Push the choke knob in completely (to the

OFF position).

Slowly press primer bulb 6 times

Squeeze and hold throttle trigger. With

thumb press fast idle lock down; then re-

lease throttle trigger.

Sharply pull the starter rope with your right

hand until the engine starts

Squeeze and release throttle trigger to al-

low engine to return to idle speed.

DIFFICULT STARTING (or starting a

flooded engine):

The engine may be flooded with too much

fuel if it has not started after 10 pulls.

Flooded engines can be cleared of excess

fuel by following the warm engine starting

procedure listed above. Insure the ON/

STOP switch is in the ON position.

Starting could require pulling the starter rope

handle many times depending on how badly

the unit is flooded. If engine fails to start, refer

to the TROUBLESHOOTING TABLE or call

1-800-554-6723.

CHAIN BRAKE

WARNING:

If the brake band is

worn too thin it may break when the chain

brake is triggered. With a broken brake band,

the chain brake will not stop the chain. The

chain brake should be replaced by an autho-

rized service dealer if any part is worn to less

than 1/32” thick. Repairs on a chain brake

should be made by an authorized service

dealer. Take your unit to the place of pur-

chase if purchased from a servicing dealer,

or to the nearest authorized master service

dealer.

This saw is equipped with a chain brake.

The brake is designed to stop the chain if

kickback occurs.

The inertia--activated chain brake is

activated if the front hand guard is pushed

forward, either manually (by hand) or

automatically (by sudden movement).

If the brake is already activated, it is

disengaged by pulling the front hand guard

back toward the front handle as far as

possible.

When cutting with the saw, the chain brake

must be disengaged.

Disengaged

Engaged

Braking function control

CAUTION:

The chain brake must be

checked several times daily. The engine

must be running when performing this proce-

dure. This is the only instance when the saw

should be placed on the ground with the en-

gine running.

Place the saw on firm ground. Grip the rear

handle with your right hand and the front han-

dle with your left hand. Apply full throttle by

fully depressing the throttle trigger. Activate

the chain brake by turning your left wrist

against the hand guard without releasing

your grip around the front handle. The chain

should stop immediately.

Inertia activating function control

WARNING:

When performing the

following procedure, the engine must be

turned off.

Grip the rear handle with your right hand and

the front handle with your left hand. Hold the

chain saw approximately 14

(35 cm) above

a stump or other wooden surface. Release

your grip on the front handle and use the

weight of the saw to let the top of the guide

bar fall forward and contact the stump.

When the tip of the bar hits the stump, the

brake should activate.

CUTTING METHODS

IMPORTANT POINTS

Check chain tension before first use and

after 1 minute of operation. See CHAIN

TENSION in the ASSEMBLY section.

Cut wood only . Do not cut metal, plastics,

masonry, non-w ood building materials, etc.

Stop the saw if the chain strikes a foreign

object. Inspect the saw and repair or re-

place parts as necessary.

Keep the chain out of dirt and sand. Even a

small amount of dirt will quickly dull a chain

and thus increa s e the possibility of kickbac k .

Practice cutting a few small logs using the

following techniques to get the “feel” of us-

ing your saw before you begin a major

sawing operation.

Squeeze the throttle trigger and allow

the engine to reach full speed before

cutting.

Begin cutting with the saw frame

against the log.

Keep the engine at full speed the entire

time you are cutting.

Allow the chain to cut for you. Exert only

light downward pressure. If you force

the cut, damage to the bar, chain, or en-

gine can result.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Commentaires sur ces manuels

Pas de commentaire

Poulan 530086667 Manuel d'utilisateur Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Outil à essence Poulan 530086667