Poulan PPB4000C Manuel d'utilisateur télécharger pdf (Page 4)

from water heaters, electric motors or

switches, furnaces, etc.

Store unit so the blade cannot accidentally

cause injury.

Store unit indoors, out of reach of children.

If situations occur which are no t co vered in this

manual, use care and good judgment. If you

need a ssistance, call 1--800--554--6723.

SPECIALNOTICE:

Exposure to vibrations

through prolonged use of gasoline powered

hand tools could cause blood vessel or nerve

damage in the fingers, hands, and joints of

people proneto circulation disorders orabnor-

mal swellings. Prolonged use in cold weather

has been linked to blood vessel damage in

otherwise healthy people. If symptoms occur

such as numbness, pain, loss of strength,

change in skin color or texture, or loss of feel-

ing in the fingers, hands, or joints, discontinue

the use of this tool and seek medical attention.

An anti-vibration system does not guarantee

the avoidance of these problems. Users who

operatepowertools on a continualandregular

basis must monitor closely their physical

condition and the condition of this tool.

SAVE THESE INSTRUCTIONS

ASSEMBLY

CARTON CONTENTS

Check carton contents for the following:

Brushcutter attachment

Handlebar (with clamp and knob)

Handlebar clamp base (with spacer tabs)

Shoulder strap

Upper shoulder strap clamp

Lower shoulder strap clamp (with spacer tabs)

Handlebar clamp screws (4)

Shoulder strap clamp screws (2)

4--point weed blade (assembled on brush-

cutter attachment)

Large nut for installing blade

Retaining washer

Cupped washer

Metal shield (assembled on brushcutter at-

tachment)

Trimmer head

Plastic shield

Wing nut (screwed onto plastic shield)

Attachment hanger

Hex wrench

W ARNING:

If received assembled, re-

peat all steps to ensure your unit is pro perly as-

sembled and all fastene rs are secure.

Examine parts for damage. Do not use dam-

aged parts.

NOTE:

If you need a ssist anceor find th at p a rts

are missing or damaged, call 1-800-554-6723.

TOOLS REQUIRED

Hex wrench (provided)

INSTALLING BRUSHCUTTER

ATTACHMENT

CAUTION:

Wh en removing or inst alling at-

tachments, place the unit on a flat surface for

st ab ility.

1. Loosen the coupler by turning the knob

counterclockwise.

Coupler

Knob

LOOSEN

TIGHTEN

2. Remove the shaft cap from the brushcut-

ter attachment (if present).

3. Position locking/release button of attach-

ment into guide recess of coupler.

4. Push the attachmentintothecoupleruntil

the locking/release button snaps into the

primary hole.

5. Before using the unit, tightenthe knob se-

curely by turning clockwise.

Coupler Primary Hole

Upper

Shaft

Locking/

Release

Button

Lower

Attachment

Guide Recess

W ARNING:

Make sure the locking/re-

lease button is locked in the primary hole and

the knob is securely tightened before operat-

ing the unit.

HANDLEBAR ASSEMBLY

DANGER:

RISK OF CUT.

To av oi d

serious injury, the barrier portion of the handlebar

must be installed as shown on the upper shaft of

the powerhead to provide a barrier between op-

erator and the spinning b lade. Attach sha ft

clamp above arrow on safety warning decal on

the uppe r shaft (powerhead end of unit). Ensure

handlebar is positioned on ha ndlebar clamp be-

tween the arrows on the handlebar decal.

NOTE:

The shaft clamp base has four

spacer tabs attached. These tabs are pro-

vided to adapt this attachment for use with

powerheads that have a 1

diameter upper

shaft(theshaft clamp will not tighten downse-

curely on the 1

diameter upper shaft without

using these spacer tabs). The tabs must be

broken off completely before use and placed

over the screw holes on the clamp base.

These tabs are not needed for powerheads

with a 7/8

upper shaft.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Poulan PPB4000C Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Poulan PPB4000C