Poulan 545137280 Manuel d'utilisateur télécharger pdf (Page 10)

OPERATION

KNOW YOUR PRUNER

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR UNIT.

Compare the illustrations with your unit to familiarize yourself with the location of the various controls

and adjustments. Save this manual for future reference.

Primer

bulb

Assist handle

Starter handle

Throttle trigger

Start lever

Shaft

Muffler

ON/OFF switch

Coupler

Pruner

Chain

Bar

Bar oil fill cap

Bar nut

Fuel mix

fill cap

Shoulder strap clamp

Attachment hanger

Line trimmer

attachment

Shield

ON/OFF SWITCH

The ON/OFF switch is located on the trigger

handle and is used to stop the engine. Move the

switch to the OFF position to stop the engine.

PRIMER BULB

The PRIMER BULB removes air from the car-

buretor and fuel lines and fills them with fuel.

Thisallowsyoutostarttheenginewithfewer

pulls on the starter rope. Activate the primer bulb

by pressing it and allowing it to return to its origi-

nal form.

START L EVER

The ST AR T LEVER helps to supply fuel to the

engine to aid in starting. Activate the starting

system by mo ving the st art le ver to t he STAR T

position. DO NOT squeeze the throttle trigger

until the engine has started and runs. After the

engine starts, allow the engine to warm--up 5

seconds, then fully squeeze the throttle trigger

to deactivate the starting system.

COUPLER

The COUPLER enables optional attach-

ments to be installed on the unit.

CHAIN TENSION

It is normal for a new chain to stretch during

first 15 minutes of operation. You should

check your chain tension frequently. See

CHAIN TENSION in the SERVICE AND AD-

JUSTMENTS section.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel

information in the safety rules before you be-

gin. If you do not understand the safety rules,

do not attempt to fuel your unit. Call

1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly

when refueling.

HELPFUL TIP

To obtain the correct oil mix

ratio, pour 3.2 ounces of

2-- cycle synthetic oil into

one gallon of fresh gas.

This engine is certified to operate on

unleaded gasoline. Before operation,

gasoline must be mixed with a good quality

synthetic 2-cycle air-cooled engine oil

designed to be mixed at a ratio of 40:1.

Poulan/WEED EA TER brand synthetic oil is

recommended. Mix gasoline and oil at a ratio

of 40:1. A 40:1 ratio is obtained by mixing 3.2

ounces (95 ml) of oil with 1 gallon (4 liters) of

unleaded gasoline. DO NOT USE a utomotive

oil or marine oil. These oils will cause engine

damage. When mixing fuel, follow instructions

printed on container. Once oil is added to

gasoline, shake container momentarily to

assure that the fuel is thoroughly mixed. Always

read and follow the safety rules relating to fuel

before fueling your unit.

BAR AND CHAIN LUBRICATION

The bar and chain require lubrication. The chain

oiler provides continuous lubrication to the chain

and guide bar. Be sure to fill the bar oil tank

when you fill the fuel tank (Capacity = 4.6 fl. oz.).

Lack of oil will quickly ruin the bar and chain.

Too little oil will cause overheating shown by

smoke coming from the chain and/or discolor-

ation of the bar. The oil output is automatically

metered during operation. Always fill the bar oil

tank when you fill the fuel tank.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 20 21

Commentaires sur ces manuels

Pas de commentaire

Poulan 545137280 Manuel d'utilisateur Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Poulan 545137280