Poulan 115274026 Manuel d'utilisateur télécharger pdf (Page 5)

S Always keep engine on the right--hand side

of your body.

S Hold the unit firmly with both hands.

S Keep firm footing and balance. Do not over-

reach.

S Keep blade or trimmer head below waist

level. Do not raise engine above your waist.

S Keep all parts of your body away from blade,

trimmer head, and muffler when engine is run-

ning. A hot muffler can cause serious burns.

S Cut from your left to your right. Cutting on

right side of the shield will throw debris

away from the operator.

S Use only in daylight or good artificial light.

S Use only for jobs explained in this manual.

TRANSPORTING AND STORAGE

S Stop the unit before carrying.

S Keep muffler away from your body.

S Allow the engine to cool and secure the unit

before storing or transporting it in a vehicle.

S Empty the fuel tank before storing or trans-

porting the unit. Use up fuel left in the carbu-

retor by starting the engine and letting it run

until it stops.

S Store unit so the blade or line limiter blade

cannot accidentally cause injury. The unit

can be hung by the shaft.

S Store unit out of reach of children.

WARNING: The engine exhaust

from this product contains chemicals known

to the State of California to cause cancer, birth

defects or other reproductive harm.

SAFETY NOTICE: Exposure to vibratio ns

through prolonged use of gasoline powered

hand tools could cause blood vessel or nerve

damage in the fingers, hands, and joints of

people prone to circulation disorders or abnor-

mal swellings. Prolonged use in cold weather

has been linked to blood vessel damage in

otherwise healthy peop le. If symptoms occur

such as numbness, pain, loss of strength,

change in skin color or texture, or loss of feeling

in the fingers, hands, or joints, discontinue the

use of this tool and seek medical attention. An

anti--vibration system does not guarantee the

avoidance of these problems. Users who oper-

ate power tools on a continual and regular basis

must monitor closely their physical condition

and the conditi on of this tool.

SPECIAL NOTICE: This unit is equipped

with a tempe rature lim iting muffle r and spark ar-

resting screen which meets the requirements of

California Codes 4442 and 4443. All U.S. forest

land and the states of California, Idaho, Maine,

Minnesota, New Jersey, Oregon, and W ashing-

ton require by law that many internal combus-

tion engines be equipped with a spark arresting

screen. If you operate in a locale where such

regulations exist, you are legally responsible for

maintaining the operating condition of these

parts. Failure to do so is a violation of the law .

For normal homeowner use, the muffler and

spark arresting screen will not require any ser-

vice. After 50 hours of use, we recommend that

your muffler be serviced or replaced by your au-

thorized service dealer .

ASSEMBLY

CARTON CONTENT S

Check carton contents against the following list:

S Powerhead

S Lower attachment (with trimmer head

installed)

S Cupped washer

S Large nut for installing blades

S Hex wrench

S Handlebar

S Bracket cover

S Bracket cover screws (2)

S Metal blade shield

S Blade shield screws (4)

S 4--point weed blade

S Plastic shield

S Wing nut (screwed onto plastic shield)

S Shoulder strap with warning

S Container of oil

WARNING: Always stop unit and dis-

connect spark plug before performing any as-

sembly procedures.

WARNING: If received assembled,

repeat all steps to ensure your unit is properly

assembled and all fasteners are secure.

Examine parts for damage. Do not use dam-

aged parts.

NOTE: If you need assistance or find parts

missing or damaged, call 1-800-554-6723.

It is normal for the fuel filter to rattle in the

empty fuel tank.

Finding fuel or oil residue on muffler is normal

due to carburetor adjustments and testing

done by the manufacturer .

TOOLS REQUIRED

S Hex wrench (provided)

S Adjustable wrench

S Phillips screwdriver

INSTALLING BR USHC UT TER

ATTACHMENT

CAUTION: When installing brushcutter at-

tachment, place the unit on a flat surface for

stability .

1. Loosen the coupler by turning the knob

counterclockwise.

Shipping

protector

Coupler

Knob

LOOSEN

TIGHTEN

2. Remove shipping protector from coupler.

3. Remove the shaft cap from the brushcutter

attachment (if present).

1 2 3 4 5 6 7 8 9 10 ... 20 21

Commentaires sur ces manuels

Pas de commentaire

Poulan 115274026 Manuel d'utilisateur Page 5

Commentaires sur ces manuels