Poulan 115274026 Manuel d'utilisateur télécharger pdf (Page 13)

more likely to occur in areas where it is

difficult to see the material being cut. By

using the unit properly , the occurrence of

blade thrust will be reduced and the

operator will be less likely to lose control.

S Cut only grass, weeds, and woody brush up

to 1/2 inch (1 cm) in diameter with the weed

blade. Do not let the blade contact material

it cannot cut such as stumps, rocks,

fences, metal, etc., or clusters of hard,

woody brush having a diameter greater

than 1/2 inch (1 cm).

S Keep the blade sharp. A dull blade is more

likely to snag and thrust.

S Cut only at full throttle. The blade will have

maximum cutting power and is less likely to

bind or stall.

S “Feed” the blade deliberately and not too

rapidly. The blade can thrust away if it is fed

too rapidly.

S Cut only from your left to your right. Cutting on

right side of the shield will throw debris away

from the operator.

S Use the shoulder strap and keep a firm grip

on the unit with both hands. A properly

adjusted shoulder strap will support the

weight of the unit, freeing your arms and

hands to control and guide the cutting motion.

S Keep feet comfortably spread apart and

braced for a possible sudden, rapid thrust of

unit. Do not overreach. Keep firm footing and

balance.

S Keep blade below waist level; it will be

easier to maintain control of unit.

S Do not raise the engine above your waist as

the blade can come dangerously close to

your body.

S Do not swing unit with such force that you

are in danger of losing your balance.

Bring the engine to cutting speed before enter-

ing the material to be cut.If the blade does not

turn when you squeeze the throttle trigger , make

sure shaft is fully inserted into the engine.

Always release the throttle trigger and allow

engine to return to idle speed when not cut-

ting. The blade should not turn while the en-

gine is running at idle. If the blade turns at idle,

do not use your unit. Refer to the CARBURE-

TOR ADJUSTMENT section or contact your

authorized service dealer.

S Maintain good firm footing while using the

unit. Do this by planting feet firmly in a

comfortable apart position.

S Cut while swinging the upper part of your

body from left to right.

S Asyoumoveforwardtothenextareatocut,

be sure to maintain your balance and footing.

Cut using the 2

o’clock to 4 o’clock

position of the

blade

2 o’clock

4 o’clock

RECOMMENDED CUTTING POSITION

WARNING: The operator or others

must not try to clear away cut material with the

engine running or the blade turning to avoid

serious injury. Stop engine and blade before

removing materials wrapped around blade or

shaft.

ADDITIONAL SAFETY RULES

FOR OPTIONAL ATTACHMENTS

WARNING: For each optional at-

tachment used, read entire instruction manu-

al before use and follow all warnings and in-

structions in manual and on attachment.

WARNING: Ensure handlebar re-

mains installed on upper shaft (engine end of

unit) at all times.

Handlebar

EDGER SAF ET Y

WARNING: Inspect the area to be

edged before each use. Remove objects

(rocks, broken glass, nails, wire, etc.) which

can be thrown by the blade or can wrap

around the shaft.

WARNING: Blade rotates momen-

tarily after the trigger is released or engine is

turned off. The blade can seriously cut you or

others. Allow blade to stop before removing it

from the cut.

S Throw away blades that are bent, warped,

cracked, broken or damaged in any other

way. Replace parts that are cracked,

chipped, or damaged before using the unit.

S Do not attempt to remove cut material nor

hold material to be cut when the engine is

running or when cutting blade is moving.

S Always keep the wheel and depth adjusting

skid in contact with the ground.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Commentaires sur ces manuels

Pas de commentaire

Poulan 115274026 Manuel d'utilisateur Page 13

Commentaires sur ces manuels