Poulan PLN3516F Manuel d'utilisateur Page 13

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 18
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 12
E. Grasp the rear handle with your right
hand. Thumb and fingers should
encircle the handle,
F. Depress the LOCK/OFF button with
your right thumb. Squeeze the trigger
with your index finger. (See Fig.4-1D).
G. While the motor is running, activate the
CHAIN BRAKE® by rolling your left
hand forward against the lever.
H. Chain and motor should stop abruptly.
WARNING
If the chain and motor fail to stop when the
CHAIN BRAKE® is engaged, take the saw
to the nearest Authorized Service Center.
Do not use the saw if the CHAIN BRAKE®
is not in proper working order.
4~5. EXTENSION CORDS
When using an electric chain saw, plug it
into the extension cord oniy when you are
ready to cut wood. Connect the extension
cord to a 110/120 voltage outlet, see chart
CAUTION
A cord that is hot to the touch is
overloaded.
WARNING
Do not operate your chain saw in a wet or
damp environment. Do not expose the saw
to rain, snow or sleet, Moisture will cause
short circuits. Replace or repair any
damaged or frayed extension cords before
using your saw. Keep the cord away from
the cutting area and position the cord so
that it will not be caught on branches or
other objects during cutting.
DOUBLE INSULATION ©WHEN
SERVICING USE ONLY IDENTICAL
REPLACEMENT PARTS
Do not use if the cord or plug is damaged.
Your appliance is double insulated to help
protect against electric shock.
Double insulation construction consists of
1wo(2) separate ‘layers" of electrical
insulation.
Appliances built with this insulation system
are not intended to be grounded. As a
result, the extension cord used with your
appliance can be plugged into any
conventional 120 volt electrical outlet.
Normal safety precautions must be
observed when operating an electrical
appliance. The double insulation system is
only for added protection against injury
resulting from a possible internal electrical
insulation failure,
WARNING
Your double insulated appliance has no
serviceable parts inside. Do not attempt to
repair it yourself. For service information,
contact the Poulan Product Service
Department tolFfree number listed on the
back cover of this manual.
5 - GENERAL CUTTING INSTRUCTIONS
5-1. FELLING
Felling is the term for cutting down a tree.
Small trees up to 6-7 inches (15-18cm) in
diameter are usually cut in a single cut.
Larger trees require notch cuts. Notch cuts
determine the direction the tree wiil fall.
FELLING A TREE:
WARNING
A retreat path (A) should be planned and
cleared as necessary before cuts are
started, The retreat path should extend
back and diagonally to the rear of the
expected line of fall, as illustrated in Figure
5-1 A.
CAUTION
If felling a tree on sloping ground, the chain
saw operator should keep on the uphill
side of the terrain, as the tree is likely to
roll or slide downhill after it is felled.
NOTE: Direction of fall (B) is controlled by
the notching cut. Before any cuts are
made, consider the location of larger
branches and natural lean of the tree to
determine the way the tree will fail.
WARNING
Do not cut down a tree during high or
changing winds or if there is a danger to
property. Consult a tree professional.
Do not cut down a tree if there is a danger
of striking utility wires; notify the utility
company before making any cuts.
GENERAL GUIDELINES FOR FELLING
TREES:
Normally felling consists of two (2) main
cutting operations, notching (C) and
making the felling cut (D). Start making the
upper notch cut (C) on the side of the tree
facing the felling direction (E). Be sure you
don’t make the lower cut too deep into the
trunk.
13
Vue de la page 12
1 2 ... 8 9 10 11 12 13 14 15 16 17 18

Commentaires sur ces manuels

Pas de commentaire