Poulan P3500 Manuel d'utilisateur télécharger pdf (Page 4)

4

SPECIAL NOTICE:

This unit is not

equipped with a temperature limiting muffler

and spark arresting screen which meets the

requirements of California Codes 4442 and

4443. All U.S. forest land and the states of

California, Idaho, Maine, Minnesota, New

Jersey, Oregon, and Washington require by

law that many internal combustion engines to

be equipped with a spark arrestor screen. If

you operate in a locale where such regula-

tions exist, you are legally responsible for

installing and maintaining the operating con-

dition of these parts. Failure to do so is a viola-

tion of the law.

ASSEMBLY

It is normal for the fuel filter to rattle in the

empty fuel tank. Finding fuel or oil residue on

muffler is normal due to carburetor adjust-

ments and testing done by the manufacturer.

ASSEMBLY

WARNING:

If received assembled,

repeat all steps to ensure your unit is properly

assembled and all fasteners are secure.

Tools you will need:

S

2 hex key wrenches (provided)

S

adjustable wrench or large pliers

S

phillips screwdriver

ATTACH THE TUBE TO THE EN-

GINE

S

Slip the tube with drive shaft into the engine.

S

Insert and tighten two screws, washers,

and nuts into clamp holes in engine.

ATTACHING THE HANDLEBAR

DANGER:

The barrier portion of the

handlebar must be installed as shown to pro-

vide a barrier between operator and the spin-

ning blade.

S

Locate the decal on the handlebar. This de-

cal includes two arrows. Position the han-

dlebar on the mounting bracket between

these arrows.

S

Position the bracket cover over the handle-

bar. Again make sure the handlebar is be-

tween the arrows.

S

Insert screws and hand tighten only. Be

sure the handlebar is installed correctly;

then, tighten each screw securely with the

large hex wrench.

Bracket Cover

Screw

Mounting

Bracket

Handlebar

FUELING

This engine is certified to operate on unleaded

gasoline. Gasoline must be mixed with a good

quality 2-cycle air-cooled engine oil designed to

be mixed at a ratio of 40:1. Poulan/Weed Eater

brand oil is recommended. (A 40:1 ratio is ob-

tained by mixing 3.2 ounces of oil w ith 1 gallon of

unleaded gasoline). When mixing fuel follow the

instructions printed on the container. Always

read and follow the safety rules under FUEL

SAFETY.

STARTING

HOW TO STOP YOUR UNIT

S

Move the ON/STOP switch to the STOP

position.

S

If engine does not stop, move choke to the

FULL CHOKE position.

HOW TO START YOUR UNIT

DANGER:

The cutting blade will

turn while starting the engine.

WARNING:

Avoid any contact with

the muffler. A hot muffler can cause serious

burns.

S

Rest engine and shield on ground, support-

ing unit, so the blade is not touching the

ground.

COLD ENGINE STARTING OR

STARTING AFTER REFUELING

S

Move the switch to the ON position.

S

Slowly press primer bulb 6 times.

S

Move the choke lever to FULL CHOKE

position.

Choke Lever

Primer bulb

ON/OFF Switch

Starter

Handle

Muffler

S

Squeeze the throttle trigger fully and hold

through

all remaining steps.

S

Pull starter rope handle sharply 6 times.

S

Move choke lever to HALF CHOKE posi-

tion.

S

Pull starter rope handle no more than 6

pulls, until engine runs.

S

Allow engine to run 10 seconds, then move

choke lever to OFF CHOKE position.

STARTING A WARM ENGINE

S

Move the switch to the ON position.

S

Move the choke lever to OFF CHOKE posi-

tion.

S

Pull starter rope handle until engine runs.

S

If engine does not start in 5 pulls, follow in-

structions in STARTING A COLD ENGINE.

1 2 3 4 5 6 7

Commentaires sur ces manuels

Pas de commentaire