Poulan 545117550 Manuel d'utilisateur télécharger pdf (Page 10)

10

ASSEMBLY

WARNING: If received assembled,

review all assembly steps to ensure your unit

is properly assembled and all fasteners are

secure.

Examine parts for damage. Do not use dam-

aged parts.

NOTE: If you need assistance or find parts

missing or damaged, call 1-800-554-6723.

TOOLS REQUIRED

S Hex wrench

S Chain adjustment tool (bar tool)

INSTALL ING PRUNER ATTACH-

MENT

CAUTION:

When removing or installing at-

tachments, place the unit on a flat surface for

stability.

1. Loosen the coupler by turning the knob

counterclockwise.

Coupler

Knob

LOOSEN

TIGHTEN

2. Remove the shaft cap from the pruner at-

tachment (if present).

3. Position locking/release button of attach-

ment into guide recess of coupler.

4. Push the attachment into the coupler until

the locking/release button snaps into the

primary hole.

5. Before using the unit, tighten the knob se-

curely by turning clockwise.

Coupler Primary Hole

Upper

Shaft

Locking/

Release

Button

Lower

Attachment

Guide Recess

WARNING: Make sure the locking/

release button is locked in the primary hole

and the knob is securely tightened before op-

erating the unit. All attachments are designed

to be used in the primary hole.

For optional attachments, see the AS-

SEMBLY section of the applicable attach-

ment instruction manual.

SHOULDER STRAP ASSEMBLY

WARNING: Proper shoulder strap

adjustments must be made with the motor

completely stopped before using unit.

1. Try on shoulder strap and adjust for fit and

balance before starting the unit or begin-

ning a cutting operation.

2. Insert your right arm and head through the

shoulder strap and allow it to rest on your

left shoulder. Make sure the danger sign

is centered on your back and the hook is

to the right side of your waist.

NOTE: A one-half twist is built in the shoul-

der strap to allow the strap to rest flat on the

shoulder.

3. Adjust the strap, allowing the hook to be

about 3 -- 6 inches (8 -- 15 cm) below the

wai st.

4. Fasten the strap hook to the clamp lo-

cated between the trigger handle and the

assist handle and lift the tool to the operat-

ing position.

NOTE: It m ay be necessary to relocate the

shoulder strap clamp on the shaft for proper

balancing of unit.

TO RELOCATE SHOULDER STRAP

CLAMP:

1. Loosen and remove both clamp screws.

2. Place the upper shoulder strap clamp

over the upper shaft.

3. Position the lower shoulder strap clamp

under the upper shaft and align the upper

and lower clamp screw holes.

Upper Shoulder

Strap Clamp

Screws

Lower Shoulder

Strap Clamp

POWERHEAD

END

ATTACHMENT

END

4. Insert two screws into the screw holes.

5. Secure shoulder strap clamp by tighten-

ing screws with a hex wrench.

ADJUSTING THE ASSIST HANDL E

WARNING: When adjusting the assist

handle during pruner use, be sure it remains be-

tween the coupler and the

lower arrow

(closest to coupler) on the safety label to ensure

proper balancing of unit. When adjusting the

assist handle during use of optional attach-

ments (or handlebar for edger attachment), it

must be repositioned between the trigger switch

and the

upper arrow (closest to motor) on

the safety label.

1. Loosen wing nut on handle.

2. Rotate the handle on the shaft to an up-

right position; retighten wing nut.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16 17

Commentaires sur ces manuels

Pas de commentaire