Poulan BVM200 Manuel d'utilisateur télécharger pdf (Page 3)

-- 3 --

disconnected. Keep vents and discharge

tubes free of debris which can accumulate

and restrict proper air flow.

Never place any object in the air intake open-

ing as this could restrict proper air flow and

cause damage to the unit.

Never use for spreading chemicals, fertiliz-

ers, or other substances which may contain

toxic materials.

To avoid spreading fire, do not use near leaf

or brush fires, fireplaces, barbecue pits,

ashtrays, etc.

Use only for jobs explained in this manual.

MAINTAIN YOUR UNIT PROPERLY

Have all maintenance other than the rec-

ommended procedures described in the in-

struction manual performed by an autho-

rized service dealer.

Disconnect s park plug before perform ing

maintenance except for carburetor adjust-

ments.

Use only recommended Poulan PRO

re-

placement parts; use of any other parts

may void your warranty and cause damage

to your unit.

Empty fuel tank before storing the unit. Use

up fuel left in carburetor by starting engine and

letting it run until it stops .

Do not use any accessory or attachment

other than those recommended by manufac-

turer for use with your unit.

Do not store the unit or fuel in a closed area

where fuel vapors can reach sparks or an

open flame from hot water heaters, electric

motors or switches, furnaces, etc.

Store in a dry area out of reach of children.

SPECIAL NOTICE:

Exposure to vibra-

tions through prolonged use of gasoline pow-

ered hand tools could cause blood vessel or

nerve damage in the fingers, hands, and

joints of people prone to circulation disorders

or abnormal swelling. Prolonged use in cold

weather has been linked to blood vessel dam-

age in otherwise healthy people. If symptoms

occur such as numbness, pain, loss of

strength, change in skin color or texture, or

loss of feeling in the fingers, hands, or joints,

discontinue the use of this tool and seek

medical attention. An antivibration system

does not guarantee the avoidance of these

problems. Users who operate power tools on

a continual and regular basis must monitor

closely their physical condition and the condi-

tion of this tool.

SPECIAL NOTICE:

For users on U .S. For-

est Land and in some states, including Cali-

fornia (Public Resources Codes 4442 and

4443), Idaho, Maine, Minnesota, New Jersey,

Oregon, and Washington: Certain internal

combustion engines operated on forest,

brush, and/or grass covered land in the above

areas are required to be equipped with a

spark arresting screen, maintained in effec-

tive working order, or the engine must be con-

structed, equipped, and maintained for the

prevention of fire. Check with your state or lo-

cal authorities for regulations pertaining to

these requirements. Failure to follow these

requirements is a violation of the law. This unit

is not factory equipped with a spark arresting

screen; however, a spark arresting screen is

available as an optional part. If a spark arrest-

ing screen is required in your area, contact

your authorized service dealer for the correct

kit. The spark arresting screen, blower tubes,

and nozzles must be assembled to unit to be

in full compliance with regulations.

ASSEMBLY

WARNING:

Stop engine and be sure

the impeller blades have stopped turning be-

fore opening the vacuum inlet door or at-

tempting to insert or remove the vacuum or

blower tubes. The rotating blades can cause

serious injury. Always disconnect the spark

plug before performing maintenance or ac-

cessing movable parts.

WARNING:

If you receive your unit

assembled, check each step to insure your

unit is properly assembled and all fasteners

are secure. Follow all safety information in

the manual and on the unit.

A standard screwdriver is required for as-

sembly.

BLOWER TUBE ASSEMBLY

Align the rib on the blower tube with the

groove in the blower outlet; slide the tube

into place.

NOTE:

Tube clamp must be loose enough to

allow blower tube to be inserted in blower out-

let. Loosen tube clamp by turning knob coun-

terclockwise.

Blower

Tube

Blower

Outlet

Rib

Groove

Tighten the tube clamp by turning the knob

clockwise.

To remove the tube, turn the knob counter-

clockwise to loosen clamp; remove tube.

VACUUM BAG ASSEMBLY

Open the zipper on the vacuum bag and in-

sert the elbow tube.

Push the small end of the elbow tube

through the small opening in the bag.

Small

Opening

Zipper

Opening

Elbow

Tube

Rib

NOTE:

Make sure edge of the small opening

is flush against the flared area of the elbow

tube, and the rib on the elbow tube is on the

bottom.

1 2 3 4 5 6 7 8 9

Commentaires sur ces manuels

Pas de commentaire

Poulan BVM200 Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Ventilateurs Poulan BVM200