Poulan Saw V28 Manuel d'utilisateur Page 6

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 23
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 5
10 11
General Operation
Always clamp the workpiece securely on a
saw horse or bench (Fig. 10). See “APPLICA-
TIONS” for the correct way to support your
work in different situations.
1. Draw a cutting line. Place the front of
the shoe on the edge of the workpiece
without making blade contact. Hold
the handle with one hand and the front
handle with the other (Fig. 12).
6. If the saw binds and stalls, maintain
a rm grip and release the trigger im-
mediately. Hold the saw motionless in
the workpiece until the blade comes to
a complete stop.
7. After nishing a cut, be sure the lower
guard closes and the blade comes to a
complete stop before setting the saw
down.
Electric Brake
The electric brake engages when the trig-
ger is released, causing the blade to stop
and allowing you to proceed with your work.
Generally, the saw blade stops within two
seconds. However, there may be a delay
between the time you release the trigger
and when the brake engages. Occasionally
the brake may miss completely. If the brake
misses frequently, the saw needs servicing
by an authorized MILWAUKEE service facil-
ity. The brake is not a substitute for the guard,
and you must always wait for the blade to
stop completely before removing the saw
from the workpiece.
Cold Weather Operation
The V28 Lithium-Ion battery pack can be
used in temperatures down to -4°F. When
the battery pack is very cold, it may pulse for
the rst minute of use to warm itself up. Put
the battery pack on a tool and use the tool in
a light application. After about a minute, the
pack will have warmed itself up and operate
normally.
Troubleshooting
If the blade does not follow a straight line:
Teeth are dull. This is caused by hitting a
hard object such as a nail or stone, dull-
ing teeth on one side. The blade tends to
cut to the side with the sharpest teeth.
Shoe is out of line or bent
Blade is bent
Rip fence or guide is not being used
If the blade binds, smokes or turns blue
from friction:
Blade is dull
Blade is on backwards
Blade is bent
Blade is dirty
Workpiece is not properly supported
Incorrect blade is being used
Fig. 11
Fig. 12
2. Line up the sight line with your cutting
line. Position your arms and body to
resist KICKBACK.
3. To start the saw, push the lock-off button
down while pulling the trigger. Allow the
motor to reach full speed before begin-
ning cut.
4. While cutting, keep the shoe at against
the workpiece and maintain a firm
grip. Do not force the saw through the
workpiece. Forcing a saw can cause
KICKBACK.
5. If making a partial cut, restarting in
mid-cut or correcting direction, allow
the blade to come to a complete stop.
To resume cutting, center the blade in
the kerf, back the saw away from cutting
edge a few inches, push the lock-off
button down while pulling the trigger and
re-enter the cut slowly.
WARNING
To reduce the risk of electric shock,
check work area for hidden pipes and
wires before making pocket cuts.
Pocket Cutting
Pocket cuts are made in the middle of the
workpiece when it can not be cut from an
edge. We recommend using a Sawzall
®
reciprocating saw or jig saw for this type
of cut. However, if you must use a circular
saw to make a pocket cut, USE EXTREME
CAUTION. To maintain control of the saw
during pocket cutting, keep both hands on
the saw.
1. Beginning at a corner, line up the sight
line with your cutting line. Tilt the saw
forward, rmly xing the front of the shoe
on the workpiece (Fig. 14). The blade
should be just above cutting line, but not
touching it. Raise the lower guard using
the lower guard lever.
Ripping Wood
Ripping is cutting lengthwise with the grain.
Select the proper blade for your job. Use a
rip fence for rips 4" wide or less. To install the
rip fence, slide the bar through the rip fence
slot in either side of the shoe. The width of
the cut is the distance from the inside of the
blade to the inside edge of the rip fence.
Adjust the rip fence for the desired width, and
lock the setting by tightening the rip fence
adjusting knob.
When ripping widths greater than 4", clamp
or tack 1" lumber to workpiece and use the
inside edge of the shoe as a guide.
Cross-Cutting Wood
Cross-cutting is cutting across the grain. Se-
lect the proper blade for your job. Advance the
saw slowly to avoid splintering the wood.
Cutting Large Panels
Large panels and long boards sag or bend
if they are not correctly supported. If you
attempt to cut without leveling and properly
supporting the workpiece, the blade will tend
to bind, causing KICKBACK.
Support large panels. Be sure to set the
depth of the cut so that you only cut through
the workpiece, not through the supports.
Fig. 13
APPLICATIONS
Fig. 14
2. To start the saw, push the lock-off button
down while pulling the trigger. Allow the
motor to reach full speed before begin-
ning cut. Using the front of the shoe
as a hinge point, gradually lower the
back end of the saw into the workpiece
(Fig. 15). Release the lower guard lever
and grasp the front handle.
Fig. 15
Vue de la page 5
1 2 3 4 5 6 7 8 9 10 11 ... 22 23

Commentaires sur ces manuels

Pas de commentaire