Poulan XT 96192004501 Manuel d'utilisateur

OWNER'S MANUALMODEL NUMBER:XT627ESSNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the Ow

10OPERATIONUSING THE CLEAN-OUT TOOL (See Fig. 14)In certain snow conditions, the discharge chute may be-come clogged with ice and snow. Use the clean-

11OPERATIONTO ADJUST SKID PLATES (See Fig. 17)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are locate

12OPERATIONTO START ENGINE Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter

13GENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. To re

14MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention

15WARNING: To avoid serious injury, before performing any service or ad just ments:1. Be sure the on/off switch is in the OFF position.2. Remove saf

16SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"

17SERVICE AND ADJUSTMENTSENGINESee engine manual.CARBURETORYour carburetor is not adjustable. Engine performance should not be affected at altitudes u

18STORAGEImmediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never store t

19TROUBLESHOOTINGDoes not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2.

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

20REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

21REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

22REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

23REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.

24REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches. 1

25REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches. 1

26REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT

27REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT

28REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT

29REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT

3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac -tured to give best possible dependability an

30REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT:

31REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT:

32REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT:

33NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement

34KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONREPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)CHASSIS /

35REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)WHEELSKEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S

36REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)BAG OF PARTSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPO

37REPAIR PARTS SNOW THROWER - MODEL XT627ES (96192004501)DECALSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT:

38SERVICE NOTES

39SERVICE NOTES

4PARTS PACKED SEPARATELY IN CARTON(1) POWER CORD(198563)(1) DISCHARGE CHUTE(3) RETAINER SPRINGS (169675)(2) SHEAR BOLTS 1/4-20 x 1-3/4(192090)(2) LOC

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-als and

5ASSEMBLY / PRE-OPERATIONNOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the ski

6ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

7OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

8OPERATIONON / OFF switch - used to STOP the engine.Traction drive control lever - used to engage power-pro pelled for ward or reverse motion of snow

9The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glas