OWNER'S MANUALMODEL NUMBER:961940009SNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the
10OPERATIONTO CONTROL SNOW DISCHARGE (See Fig. 13)WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or
11TO MOVE FORWARD AND BACKWARD (See Fig. 16)SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive con
12TO ADJUST SKID PLATES (See Fig. 18)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each
13OPERATIONSNOW THROWING TIPS• Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to adjust speed.•
14MAINTENANCELUBRICATION CHARTGENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator
15MAINTENANCESNOW THROWERAlways observe safety rules when performing main te nance.TIRES• Maintain proper air pressure in both tires (14–17 P.S.I.
16SERVICE AND ADJUSTMENTSWARNING: To avoid serious injury, beforeperforming any service or ad just ments:1. Be sure the on/off switch is in the OFF po
17SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"
18NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also preve
19STORAGEImmediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never
2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure
20TROUBLESHOOTINGDoes not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2.
21NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement
22REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)AUGER HOUSING / IMPELLER ASSEMBLY1011111111123456799981212131415161718192021212222232324
23REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches.
24NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement
25KEY PART NO. NO. DESCRIPTIONREPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)CONTROL PANEL / DISCHARGE CHUTENOTE: All compon
26REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)CONTROL PANEL / DISCHARGE CHUTEKEY PART NO. NO. DESCRIPTIONKEY PART NO.
27REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)HANDLESKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTION1
28REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA
29REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA
3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u -fac tured to give best possible dependability an
30REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)HANDLESKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTION1
31REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT
32REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)DRIVE99111111123215612131415201516171098723195353535325262627394041424344323853533736353
33REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)DRIVEKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONNOT
34REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1 in
35REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1 in
36KEY PART NO. NO. DESCRIPTIONREPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)WHEELS101055667799881516161717 18191920201111112
37REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)WHEELSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTAN
38NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement
39REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000901)DECALS14961031KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in
4PARTS PACKED SEPARATELY IN CARTON(3) RETAINER SPRINGS (169675)(1) WASHER 3/8(19131316)(1) LOCKNUT 3/8(73800600) SAFTEY IGNITION KEY(S)(422663)(1) MU
LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w
5ASSEMBLY / PRE-OPERATIONRead these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Rea
6ASSEMBLY / PRE-OPERATIONINSTALL TRACTION DRIVE CONTROL ROD(See Figs. 3 and 4)The traction drive control rod is installed on the snow thrower.1. Remo
7ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins
8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with
9MEETS A.N.S.I. SAFETY REQUIREMENTSOur snow throwers conform to the standards of the American National Standards Institute.FIG. 10OPERATIONDrive speed
Commentaires sur ces manuels