Poulan 96192001706 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Voitures Poulan 96192001706. Poulan 96192001706 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 40
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
OWNER'S MANUAL
MODEL NUMBER:
PR8527ES
SNOW THROWER
Always Wear Eye Protection During Operation
IMPORTANT MANUAL Do Not Throw Away
WARNING:
Read the Owner's Manual and
fol low all Warnings and Safety
In struc tions. Fail ure to do so
can result in serious injury.
421899 10.02.08 SR
Printed in the U.S.A.
Vue de la page 0
1 2 3 4 5 6 ... 39 40

Résumé du contenu

Page 1 - PR8527ES

OWNER'S MANUALMODEL NUMBER:PR8527ESSNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the O

Page 2 - IMPORTANT

10OPERATIONUSING THE CLEAN-OUT TOOL (See Fig. 14)In certain snow conditions, the discharge chute may be-come clogged with ice and snow. Use the clean-

Page 3 - TABLE OF CONTENTS

11OPERATIONTO ADJUST SKID PLATES (See Fig. 16)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are locate

Page 4 - ASSEMBLY / PRE-OPERATION

12OPERATIONCOLD START - ELECTRIC STARTER1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT tu

Page 5

13GENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. To re

Page 6

14MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention

Page 7

15CAUTION: Do not substitute. Use only original equip ment capscrew/shear bolts as sup plied with your snow thrower.4. Connect spark plug wire to spa

Page 8

16SERVICE AND ADJUSTMENTSWARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly

Page 9

17SERVICE AND ADJUSTMENTSSTORAGEImmediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more

Page 10 - OPERATION

18STORAGECYLINDER1. Remove spark plug.2. Pour one ounce (29 ml) of oil through spark plug hole into cylinder.3. Pull recoil starter handle slowly a

Page 11

19Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition

Page 12

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

Page 13 - MAINTENANCE

20REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches

Page 14

21REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inches

Page 15 - SERVICE AND ADJUSTMENTS

22NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 16

23NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 17

24REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

Page 18

25REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

Page 19 - PROBLEM CAUSE CORRECTION

26REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPOR

Page 20 - 01.07.002-A

27REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPOR

Page 21

28REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPOR

Page 22

29NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 23

3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac -tured to give best possible dependability an

Page 24 - 01.09.001-A

30REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

Page 25

31REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

Page 26 - 01.05.004-B

32REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTA

Page 27

33REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1

Page 28

34REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1

Page 29

35REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)WHEELSKEY PARTNO. NO. DESCRIPTION NOTE: All component dimensions given in U.S.

Page 30

36REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)BAG OF PARTSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

Page 31

375314217689REPAIR PARTS SNOW THROWER - - MODEL NO. PR8527ES (96192001706)DECALSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.

Page 32 - 01.03.005-B

38SERVICE NOTES

Page 33 - 01.00.008-B

39SERVICE NOTES

Page 34 - 01.04.019-A

4PARTS PACKED SEPARATELY IN CARTON(1) POWER CORD(198563)(1) DISCHARGE CHUTE(3) RETAINER SPRINGS (169675)(1) TRACTION DRIVE CONTROL ROD(2) SHEAR BOLTS

Page 35

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w

Page 36 - 01.14.008-A

5ASSEMBLY / PRE-OPERATIONNOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the ski

Page 37

6ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

Page 38 - SERVICE NOTES

7OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

Page 39

8OPERATIONThrottle/engine control - used to se lect either FAST or SLOW engine speed and to STOP the engine.Traction drive control lever - used to eng

Page 40 - LIMITED WARRANTY

9The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glas

Modèles reliés 421899

Commentaires sur ces manuels

Pas de commentaire