Poulan 422088 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Voitures Poulan 422088. Poulan 422088 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 40
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
OWNER'S MANUAL
MODEL NUMBER:
XT1053ES
SNOW THROWER
Always Wear Eye Protection During Operation
IMPORTANT MANUAL Do Not Throw Away
WARNING:
Read the Owner's Manual and
fol low all Warnings and Safety
In struc tions. Fail ure to do so
can result in serious injury.
422088 10.02.08 SR
Printed in the U.S.A.
Vue de la page 0
1 2 3 4 5 6 ... 39 40

Résumé du contenu

Page 1 - XT1053ES

OWNER'S MANUALMODEL NUMBER:XT1053ESSNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the O

Page 2 - IMPORTANT

10The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety gla

Page 3 - TABLE OF CONTENTS

11TO MOVE FORWARD AND BACKWARD (See Fig. 17)SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive con

Page 4 - ASSEMBLY / PRE-OPERATION

12TO ADJUST SKID PLATES (See Fig. 19)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each

Page 5

13OPERATIONTO START ENGINE • Be sure fuel shut-off valve is in the OPEN position.Your snow thrower engine is equipped with both a 120 Volt A.C. elect

Page 6

14MAINTENANCELUBRICATION CHARTGENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator

Page 7

15MAINTENANCEBELTSCheck belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not ad just able. R

Page 8

16SERVICE AND ADJUSTMENTSWARNING: To avoid serious injury, before performing any service or ad -just ments:1. Be sure throttle is in STOP position.2.

Page 9

17SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"

Page 10 - OPERATION

18STORAGEImmediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never

Page 11

19TROUBLESHOOTINGDoes not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2.

Page 12

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

Page 13

202 (EXPLODED)210911111312124131415178711561116183519212223242523222120362627283029313132333401.07.004-BREPAIR PARTS SNOW THROWER - - MODEL NUMBER X

Page 14 - MAINTENANCE

21NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 15

22NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 16 - SERVICE AND ADJUSTMENTS

23KEY PART NO. NO. DESCRIPTION12344301.11.001-AKEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inche

Page 17

24KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm

Page 18 - SNOW THROWER

25NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 19 - TROUBLESHOOTING

26NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 20

27NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 21

28NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 22 - 01.07.003-A

29NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 23 - 01.07.019-A

36. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel-ler and all moving parts have stopp

Page 24 - CONTROL PANEL / CHUTE

30REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT1053ES (96192002402)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMP

Page 25

31NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 26 - 01.05.004-B

32KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm

Page 27

33KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm

Page 28

34NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 29 - 01.10.007-B

35NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

Page 30

36KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm

Page 31

37KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTION101.14.008-A1 35062 SA

Page 32

38KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm

Page 33 - 01.00.008-B

39SERVICE NOTES

Page 34 - 01.04.019-A

4PARTS PACKED SEPARATELY IN CARTON(1) POWER CORD(198563)(1) DISCHARGE CHUTE(3) RETAINER SPRINGS (169675)(1) TRACTION DRIVE CONTROL ROD(2) SHEAR BOLTS

Page 35 - 01.15.003-A

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w

Page 36 - 01.15.001-A

5ASSEMBLY / PRE-OPERATIONNOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the ski

Page 37 - 01.14.003-A

6ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

Page 38

7CHECK TIRE PRESSUREThe tires on your snow thrower were overinflated at the fac-tory for shipping purposes. Correct and equal tire pres sure is impor

Page 39 - SERVICE NOTES

8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

Page 40 - LIMITED WARRANTY

9OPERATIONLH and RH turn triggers - used to steer the snow thrower.Drive speed control lever - used to select forward or reverse motion and speed of s

Modèles reliés 96192002402

Commentaires sur ces manuels

Pas de commentaire